|
|
|
AB-8/ Selection Of Mosfets In Switch Mode Dc-Dc Converters - Fairchild
Application Notes / (app note added 6/06) |
|
AB-9/ Suppressing Mosfet Gate Ringing In Converters: Selection Of a Gate
Resistor - Fairchild Application Notes / (app note added 6/06)
|
|
ABR-6001/ Rc5051 Converter Design Template - Fairchild Application
Notes / (app note added 6/06) |
|
ABR-6002/ Rc5051 Dc-Dc Converter - Fairchild Application Note
(app note added 2/06) |
|
ABT Design Considerations for Fault Tolerant Backplanes - National
Application Note (app not added 3/03) |
|
AC Switching with TRIAC From TTL - The MC3032 is an optoisolator TRIAC
driver. The 180-ohm resistor sets the current for the LED emitter in the
optoisolator. Change the value of this resistor - if necessary - to get
reasonable current (e.g., 15 mA). Note that you cannot test this circuit without
a load. The TRIAC will not switch unless connected to an AC voltage source, so
you can't test it for simple switching w/o applying AC and a load. Note the 500V
rating on the .01 cap....(ASCII design added 4/03) |
|
Access odd memory locations without hardware - 05/27/99 EDN-Design
Ideas Some risc controllers, like the NEC V850 family, use an internal
32-bit architecture with an external 16-bit bus. The architecture also allows
interfaces with 8-bit memories. However…PDF has several circuits, please scroll
to find this one…. [Design Idea by Sorin Zarnescu, NEC Electronics, Santa Clara,
CA] |
|
Accessing EEPROM using I2CBUS - Toshiba 870X Series Application Note
(app note added 2/06) |
|
Accurate USB 2.0 temperature sensor needs only a handful of parts -
24-May-07 Issue of EDN A USB-to-serial converter forms the heart of an
accurate USB temperature sensor.... [Design Idea by Silvio Lauckner, Ismaning,
Germany] |
|
Achieve simple IR data transmission from a PC’s serial port -
11-Oct-07 Issue of EDN By transmitting appropriate hex values from a PC's
serial port to a pair of IR LEDs, a remote-control IR receiver can enable
38.4-kHz data transmission.... [Design Idea by Andreas Grün, Wedemark, Germany] |
|
Active Termination for Scsi-2 Bus - Linear Technology App Note 34, May
1990 (electronic design idea added 12/06) |
|
Active-filter circuit and oscilloscope inspect a Class D amplifier's output
- 1-Dec-06 Issue of EDN Ease debugging of bridge-output
pulse-width-modulated audio amplifiers with this circuit.... [Design Idea by
John Guy, Maxim Integrated Products Inc, Sunnyvale, CA; Edited by Brad Thompson
and Fran Granville] |
|
Active-pullup/pulldown network saves watts - 17-Feb-05 Issue of EDN
The control circuit in Figure 1 presents a relatively low input resistance and
thus imposes a low value on external pulldown resistor R1 to provide the desired
low-level input voltage. In turn, R1 wastes power by drawing a relatively high
current through switch S1. For example, suppose that the control circuit
presents an input resistance of 2.... [Design Idea by JB Guiot, DCS Dental AG,
Allschwil, Switzerland] |
|
AD7574 Analog to Microprocessor Interface - AN-293 Analog Devices
Application Notes (app note added 6/06) |
|
Adaptive Differential Pulse Code Modulation using the PIC16/17 -
Microchip Application Note Published 26-Aug-97 (app note added 2/06)
|
|
ADC interface conditions high level signals - 30-Oct-03 Issue of EDN
Designers who build equipment for the industrial market share a widespread
problem. At one extreme, they must build equipment that supports ±10V bipolar
voltages, often riding on a high common-mode level, a requirement enforced by 30
years of legacy industrial equipment. At the other extreme, the analog signal
needs conditioning to match the full-scale range of a low-voltage,
single-supply.... [Design Idea by Moshe Gerstenhaber and Stephen Lee, Analog
Devices, Wilmington, MA] |
|
ADC16071/ADC16471 Analog Layout & Interface Design Considerations -
National Application Note (app not added 3/03) |
