Power Supplies:
Switch Mode
Page 5
Switchmode Power Supply:
#'s-A, B-E,
F-R,
S,
T-V
Boost, Buck,
Buck/Boost
Power Supplies -- Main
Page
Converters -- Main Page
Last Updated on:
Thursday, November 30, 2017 04:30 PM |
|
|
Links to electronic circuits, electronic schematics, designs for engineers,
hobbyists, students & inventors:
|
|
Tapped inductor, boost regulator deliver high voltage - 20-Jul-06
Issue of EDN Obtain 100V dc from a 3V source.... [Design Idea by David
Ng and Adam Huff, Linear Technology Corp, Milpitas, CA; Edited by Brad
Thompson and Fran Granville] |
|
TB081: Soft-Start Controller for Switching Power Supplies -
Microchip Application Note Published 29-Nov-04 (app note added 2/06)
|
|
Telephone Ring Generator using Switching Power Supply - The
telephone ring generator shown below generates the needed high voltage from
a simple switching mode power supply (SMPS) which employs a CMOS Schmitt
Trigger square wave oscillator, 10 mH inductor, high voltage switching
transistor (TIP47 or other high voltage, 1 amp transistor) and a driver
transistor (2N3053). The inductor should have a low DC resistance of 1.5
ohms or less. The switching supply must have a load connected to prevent the
voltage from rising too high, so a 22K resistor is.... [Bill Bowden's
circuit |
|
|
|
|
Two Cores Marry Make Swinging Choke - 05/11/95 EDN-Design Ideas....Designing
an output choke for a switch-mode power supply that must operate over large load
variations can be problematic. If you design the inductor for the maximum load the
power converter will see, the inductance will be below the critical inductance
required at light load. This inadequate inductance will cause the voltage on the
output capacitor to peak up, resulting in increased ripple on the output....[Design
Ideaadded 2/06] EDN is migrating links. This link is not verified. Search the
"title" EDN for new link. |
|
|
[_OLD-ads-dont_upload/OLD I-ADS from web/ad-djandassoc.htm] |
|
|
Two Watt Switching Power Supply - from 6V to14V (added 6/06) |
|
UltraLow Noise Switching Power Supplies Simplify EMI Compliance - DN316
Design Notes (Linear Technology) (app note added 1/06) |
|
Use a 555 timer as a switch-mode power supply - 14-Nov-02 Issue of EDN
Most switch-mode power supplies rely on a PWM (pulse-width-modulated] output that is
controlled via voltage feedback. A 555-timer IC can inexpensively perform PWM. The
circuit in Figure 1 shows how to turn a 555 PWM circuit into an switch-mode power
supply with only one simple equation. The design uses two 555s.... [Design Idea by
Aaron Lager, Masterwork Electronics, Rohnert Park, CA] |
|
Use a microcontroller to design a boost converter - 4-Mar-04 Issue of EDN
Boost converters, like other switchers, have traditionally received their control
signals from a dedicated circuit. However, a recent trend is to integrate simple
switching-power-supply building blocks into generic devices, such as microcontrollers.
An excellent example of this concept is a microcontroller that combines digital and
analog circuitry and makes it easier to build simple power supp.... [Design Idea by
Ross Fosler, Microchip Technology, Chandler, AZ] |
|
Various Switching Power supplies - Page has several circuits, please scroll
through all of them |
|
Whistle on Whistle Off - This CMOS toggle flip flop circuit has an addition
of2bandpass filters and condenser microphone so the relay can be toggled by whistling
at it…. [Bill Bowden's website] |
|
|
|
|
Switchmode Power Supply:
#'s-A,
B-E,
F-R,
S,
T-V |
|
|
