|
Tonemender - The Tonemender is a very flexible, yet simple clean boost with a 3-knob tonestack that allows the user to re-create the classic Fender, Marshall and Vox responses. We suggest using a TLC2272 for the dual op-amp. The TLC2272 is rated for low-noise and rail-to-rail output, which will offer the highest possible clean boost and dynamic range. The NE5532 is another good choice, but a TL072 can also be used with decent results __ Contact: holler @ runoffgroove.Com
Touch-Sensitive Musical Bell with Timer - This circuit is built around CMOS
IC CD4011 and popular melody generator IC UM66. When touch plates are bridged by hand for a moment. the circuit starts to generate music. After __ 01/01/07EFY
Toy Organ - Some useful circuits using the LM555 IC. Scroll to find the toy organ circuit __ Designed by Jose Pino
TPA3007d1 Evaluation Module - The TPA3001D1 is a 20-W mono Class-D audio power amplifier designed for 12V to 18V applications with a 4to 8-Ohm minimum speaker impedance. The efficient Class-D operation reduces solution size and cost by eliminating the need for heat sinks
Transformer Short Tester - Transformer Short Tester __ Designed by Guitar Effect RC Keen
Transistor linearly digitizes airflow - 09/19/02 EDN-Design Ideas A sensitive and reliable way to measure airflow is to take advantage of the predictable relationship between heat dissipation and air speed. The principle of thermal anemometry relies on King's Law, which dictates that the power required to maintain a fixed differential between the surface of a heated sensor and the ambient air temperature increases as the square root of air speed Design by Steve Woodward, University of North Carolina, Chapel Hill, NC
Transistor Organ - This simple circuit can provide hours of enjoyment as you learn tunes, play duets or just make some really weird sounds by pushing all the buttons at once. You have probably seen this circuit before, it is fairly common. I have seen it in several __ Designed by Aaron Cake
Transmission Line Enclosure Speakers - Built for my Ambisonic surround rig, and an interesting project. But don't do this unless you're clinically insane; Buy them instead. __ Designed by Henry
Transposable Chord Generator - This circuit consists of three precise triangle-wave oscillators, each using an Analog Devices type AD654 voltage controlled oscillator (VCO) and an AD620 instrumentation amplifier (INAMP). Each oscillator frequency (F1, F2, F3) is adjusted with a ten-turn potentiometer. The three triangle waves are summed at U1B to produce a triad chord. Transposition of the triad over a wide range is achieved by dividing each of the input voltages by a common factor, set by the TRANSPOSE potentiometer and buffered by U1A. __ Designed by Arthur Harrison
Treble Booster/Overdrive including a peRF board layout - A stone cold crazy treble-boosted overdrive. __ Contact: holler @ runoffgroove.Com
Tremolo Effect for Electric Guitar or Other Musical Instruments - Tremolo circuit is a kind of sound effect. We can see this type of effect is applied in guitar effect pedals. Tremolo effect is produced if we modulate the amplitude of an audio signal. The shape of modulating signal can vary from square wave, sawtooth, or sine. When we use a square wave, then the effect produce a knocking-like sound which might be perceived like a percussive instrument.
Tremolo Unit - A versatile guitar effect. This is a simple circuit that gives very good results __ Designed by Rod Elliott ESP
Tremolo Unit for Musicians - Jazz up your music with this easy to build unit. __ SiliconChip
Triple Spring Reverb - A spring reverb unit using three high quality Accutronics spring tanks with different decay times and feedback controls. __ Designed by Henry
Triple Video Line Driver (DC Coupled) - In DC-coupled systems, the video swings are fixed in relation to the supplies used, so back-terminated cable drivers need only provide 2V of output range when optimally biased. In most cases, this permits operation on lower power supply potential (s) than with AC-coupling (unclamped mode). Generally DC-coupled circuits use split __ Linear Technology/Analog Devices App Note, Mar 25th 2010
Tri-Vibe - A versatile modulation effect that offers true vibrato. __ Contact: holler @ runoffgroove.Com
Tube Car Stereo Amp - YES, a tube amp in a CAR!!! __ Designed by Bob Danielak
Tube Screamer-based overdrive - Tube Screamer-based overdrive. __ Contact: holler @ runoffgroove.Com
Tube Sound Fuzz Adaptation - Mark Hammer's Tube Sound Fuzz Adaptation __ Designed by Guitar Effect RC Keen
Twin Line Telebalance Unit - Again, made for Radio Glen. Quote from then station manager Lex, "Beats the living fish out of those analogue Sonifex units. " __ Designed by Henry
Two 9v battery-powered Amps based on the LM386. Schematic & PCB/perfboard layouts. - For better compatibility with effects driving the Little Gem, a FET buffer can be added. Both the Little Gem Mk II (seen below) and Ruby schematics include a simple buffer design. No further circuit modifications are necessary, however the input capacitor value of the amp may need to be adjusted to taste. __ Contact: holler @ runoffgroove.Com
Two channel distortion - Two channels of buxom distortion. __ Contact: holler @ runoffgroove.Com
Two Channel Power Amplifier - The design of our power amplifier is based on a general purpose power amplifier widely used in the electronics world. The chip (NTE 1606) we are using is used in many consumer stereo systems. We did some research and came out with a simple design that uses the NTE 1606 Power Amplifier chip
Two Terminal Current Regulator (LT1635) - The LT1635 combines an op amp with a 200mV reference. Scaling this reference voltage to a potential across resistor R3 forces a controlled amount of current to flow from the +terminal to the –terminal. Power is taken from the loop. __ Linear Technology/Analog Devices App Note, Mar 31, 2010 |
